RFC1743 日本語訳
1743 IEEE 802.5 MIB using SMIv2. K. McCloghrie, E. Decker. December 1994. (Format: TXT=43224 bytes) (Obsoletes RFC1231) (Obsoleted by RFC1748) (Status: DRAFT STANDARD)
プログラムでの自動翻訳です。
RFC一覧
英語原文
Network Working Group K. McCloghrie Request for Comments: 1743 E. Decker Obsoletes: 1231 cisco Systems, Inc. Category: Standards Track December 1994
McCloghrieがコメントのために要求するワーキンググループK.をネットワークでつないでください: 1743年のE.デッカーは以下を時代遅れにします。 1231年のコクチマスSystems Inc.Category: 標準化過程1994年12月
IEEE 802.5 MIB using SMIv2
SMIv2を使用するIEEE802.5MIB
Status of this Memo
このMemoの状態
This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.
このドキュメントは、インターネットコミュニティにインターネット標準化過程プロトコルを指定して、改良のために議論と提案を要求します。 このプロトコルの標準化状態と状態への「インターネット公式プロトコル標準」(STD1)の現行版を参照してください。 このメモの分配は無制限です。
Table of Contents
目次
1. Introduction ............................................. 1 2. The SNMPv2 Network Management Framework .................. 2 2.1 Object Definitions ...................................... 2 3. Overview ................................................. 2 3.1 MAC Addresses ........................................... 3 3.2 Relationship to RFC 1213 ................................ 3 3.3 Relationship to RFC 1573 ................................ 3 3.3.1 Layering Model ........................................ 3 3.3.2 Virtual Circuits ...................................... 3 3.3.3 ifTestTable ........................................... 3 3.3.4 ifRcvAddressTable ..................................... 4 3.3.5 ifPhysAddress ......................................... 4 3.3.6 ifType ................................................ 4 4. Definitions .............................................. 4 5. Acknowledgements ......................................... 23 6. References ............................................... 23 Appendix A. Changes from RFC 1231 ........................... 24 Security Considerations ..................................... 24 Authors' Addresses .......................................... 25
1. 序論… 1 2. SNMPv2ネットワークマネージメントフレームワーク… 2 2.1 オブジェクト定義… 2 3. 概要… 2 3.1 MACアドレス… 3 RFC1213との3.2関係… 3 RFC1573との3.3関係… 3 3.3 .1レイヤリングモデル… 3 3.3 .2 仮想の回路… 3 3.3 .3ifTestTable… 3 3.3 .4ifRcvAddressTable… 4 3.3 .5ifPhysAddress… 4 3.3 .6ifType… 4 4. 定義… 4 5. 承認… 23 6. 参照… 23 付録A.はRFC1231から変化します… 24 セキュリティ問題… 24人の作者のアドレス… 25
1. Introduction
1. 序論
This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes managed objects used for managing subnetworks which use the IEEE 802.5 Token Ring technology described in 802.5 Token Ring Access Method and Physical Layer Specifications, IEEE Standard 802.5-1989 [7]. This memo is a replacement for RFC 1231.
ネットワーク管理プロトコルがインターネットコミュニティにある状態で、このメモは使用のために、Management Information基地の一部(MIB)を定義します。 特に、それは802.5Token Ring Access MethodとPhysical Layer Specifications(IEEE Standard802.5-1989[7])で説明されたIEEE802.5Token Ring技術を使用するサブネットワークを管理するのに使用される管理オブジェクトについて説明します。 このメモはRFC1231への交換品です。
McCloghrie & Decker [Page 1] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[1ページ]RFC1743IEEE802.5MIB
2. The SNMPv2 Network Management Framework
2. SNMPv2ネットワークマネージメントフレームワーク
The SNMPv2 Network Management Framework consists of four major components. They are:
SNMPv2 Network Management Frameworkは4個の主要コンポーネントから成ります。 それらは以下の通りです。
o RFC 1442 [1] which defines the SMI, the mechanisms used for describing and naming objects for the purpose of management.
o SMI、オブジェクトを管理の目的にちなんで説明して、命名するのに使用されるメカニズムを定義するRFC1442[1]。
o STD 17, RFC 1213 [2] defines MIB-II, the core set of managed objects for the Internet suite of protocols.
o STD17、RFC1213[2]はMIB-II、管理オブジェクトの巻き癖をプロトコルのインターネットスイートと定義します。
o RFC 1445 [3] which defines the administrative and other architectural aspects of the framework.
o フレームワークの管理の、そして、他の建築局面を定義するRFC1445[3]。
o RFC 1448 [4] which defines the protocol used for network access to managed objects.
o 管理オブジェクトへのネットワークアクセスに使用されるプロトコルを定義するRFC1448[4]。
The Framework permits new objects to be defined for the purpose of experimentation and evaluation.
Frameworkは、新しいオブジェクトが実験と評価の目的のために定義されるのを可能にします。
2.1. Object Definitions
2.1. オブジェクト定義
Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the subset of Abstract Syntax Notation One (ASN.1) defined in the SMI. In particular, each object type is named by an OBJECT IDENTIFIER, an administratively assigned name. The object type together with an object instance serves to uniquely identify a specific instantiation of the object. For human convenience, we often use a textual string, termed the descriptor, to refer to the object type.
管理オブジェクトはManagement Information基地と呼ばれた仮想情報店かMIBを通してアクセスされます。 MIBのオブジェクトは、SMIで定義された抽象的なSyntax Notation One(ASN.1)の部分集合を使用することで定義されます。 特に、各オブジェクト・タイプはOBJECT IDENTIFIER、行政上割り当てられた名前によって命名されます。 オブジェクトインスタンスに伴うオブジェクト・タイプは、唯一オブジェクトの特定の具体化を特定するのに勤めます。 人間の便宜のために、私たちはしばしば記述子と呼ばれた原文のストリングを使用して、オブジェクトについて言及するのはタイプされます。
3. Overview
3. 概要
This memo defines three tables: the 802.5 Interface Table, which contains state and parameter information which is specific to 802.5 interfaces, the 802.5 Statistics Table, which contains 802.5 interface statistics, and the 802.5 Timer Table, which contains the values of 802.5-defined timers. A managed system will have one entry in the 802.5 Interface Table and one entry in the 802.5 Statistics Table for each of its 802.5 interfaces. The 802.5 Timer Table is obsolete, but its definition has been retained in this memo for backward compatibility.
このメモは3個のテーブルを定義します: 802.5Interface Table。(そのInterface Tableは状態と802.5のインタフェースに特定のパラメタ情報と802.5Statistics Tableと802.5Timer Tableを含みます)。(Statistics Tableは802.5のインタフェース統計を含みます)。(Timer Tableは802.5で定義されたタイマの値を含みます)。 管理されたシステムには、802.5Interface Tableの1つのエントリーとそれぞれの802.5のインタフェースへの802.5Statistics Tableの1つのエントリーがあるでしょう。 802.5Timer Tableは時代遅れですが、定義は後方の互換性のためのこのメモで保有されました。
This memo also defines OBJECT IDENTIFIERs, some to identify interface tests for use with the ifTestTable [6], and some to identify Token Ring interface Chip Sets.
また、このメモはOBJECT IDENTIFIERs(Token RingインタフェースChip Setsを特定するために使用のためのインタフェーステストをifTestTable[6]、およびいくつかと同一視するいくつか)を定義します。
McCloghrie & Decker [Page 2] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[2ページ]RFC1743IEEE802.5MIB
3.1. MAC Addresses
3.1. MACアドレス
All representations of MAC addresses in this MIB Module use the MacAddress textual convention [5] for which the address is in the "canonical" order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 requires MAC addresses to be transmitted most significant bit first.
MACの表現がすなわち、まるで802.5ですが、最初にそれが伝えられた最下位ビットであるかのようにアドレスがIEEE 802.1aによって定義された「正準な」オーダーにあるMacAddressの原文のコンベンション[5]にこのMIB Module使用で演説するすべてが、最初にMACアドレスが伝えられた最上位ビットであることを必要とします。
16-bit addresses, if needed, are represented by setting their upper 4 octets to all zeros, i.e., AAFF would be represented as 00000000AAFF.
必要であるなら、16ビットのアドレスは彼らの上側のすべてのゼロ4つの八重奏対八重奏を設定することによって、表されます、すなわち、AAFFが00000000AAFFとして表されるでしょう。
3.2. Relationship to RFC 1213
3.2. RFC1213との関係
When this MIB module is used in conjunction with the "old" (i.e., pre-RFC 1573) interfaces group, the relationship between an 802.5 interface and an interface in the context of the RFC 1213 is one- to-one. That is, the value of an ifIndex object instance for an 802.5 interface can be directly used to identify corresponding instances of the objects defined in this memo.
いつこのMIBモジュールは(すなわち、RFCのプレ1573)インタフェースが分類する「古さであること」に関連して使用されて、RFC1213の文脈の802.5インタフェースとインタフェースとの関係は1対-1であるか。 このメモで定義されたオブジェクトの対応するインスタンスを特定するのに直接すなわち、802.5インタフェースへのifIndexオブジェクトインスタンスの値を使用できます。
3.3. Relationship to RFC 1573
3.3. RFC1573との関係
RFC 1573, the Interface MIB Evolution, requires that any MIB module which is an adjunct of the Interface MIB, clarify specific areas within the Interface MIB. These areas were intentionally left vague in RFC 1573 to avoid over constraining the MIB module, thereby precluding management of certain media-types.
RFC1573(Interface MIB Evolution)はそれを必要とします。Interface MIBの付属物であり、Interface MIBの中で特定の領域をはっきりさせるどんなMIBモジュール。 これらの領域はMIBモジュールを抑制する上で避けるRFC1573年に故意にあいまいなままにされました、その結果、あるメディアタイプの管理を排除します。
Section 3.3 of RFC 1573 enumerates several areas which a media- specific MIB module must clarify. Each of these areas is addressed in a following subsection. The implementor is referred to RFC 1573 in order to understand the general intent of these areas.
RFC1573のセクション3.3はメディアの特定のMIBモジュールがはっきりさせなければならないいくつかの領域を列挙します。 それぞれのこれらの領域は次の小区分で扱われます。 作成者は、これらの領域の総合的目的を理解するのにRFC1573を参照されます。
3.3.1. Layering Model
3.3.1. レイヤリングモデル
For the typical usage of this IEEE 802.5 MIB module, there will be no sub-layers "above" or "below" the 802.5 interface. However, this MIB module does not preclude such layering.
このIEEE802.5MIBモジュールの典型的な用法のために、802.5が連結する“above"か“below"副層は全くないでしょう。 しかしながら、このMIBモジュールは、層にしながら、そのようなものを排除しません。
3.3.2. Virtual Circuits
3.3.2. 仮想の回路
802.5 does not support virtual circuits.
802.5 仮想の回路を支えません。
3.3.3. ifTestTable
3.3.3. ifTestTable
This MIB module defines two tests for 802.5 interfaces: Insertion and Loopback. Implementation of these tests is not required.
このMIBモジュールは2つのテストを802.5のインタフェースと定義します: 挿入とループバック。 これらのテストの実装は必要ではありません。
McCloghrie & Decker [Page 3] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[3ページ]RFC1743IEEE802.5MIB
3.3.4. ifRcvAddressTable
3.3.4. ifRcvAddressTable
The ifRcvAddressTable is defined to contains all MAC addresses, unicast, multicast (group) and broadcast, for which an interface will receive packets. For 802.5 interfaces, its use includes functional addresses. The format of the address, contained in ifRcvAddressAddress, is the same as for ifPhysAddress.
ifRcvAddressTable(インタフェースはパケットを受ける)はすべてのMACアドレス、ユニキャスト、マルチキャスト(グループ)を含んで、放送するのが定義されます。 802.5のインタフェースに関しては、使用は機能アドレスを含んでいます。 アドレスのifRcvAddressAddressに含まれた形式はifPhysAddressのように同じです。
For functional addresses on a particular 802.5 interface, only one ifRcvAddressTable entry is required. That entry is the one for the address which has the functional address bit ANDed with the bit mask of all functional addresses for which the interface will accept frames.
特定の802.5インタフェースに関する機能アドレスにおいて、1つのifRcvAddressTableエントリーだけが必要です。 そのエントリーはインタフェースがフレームを受け入れるすべての機能アドレスの噛み付いているマスクがある機能アドレスビットANDedを持っているアドレスのためのものです。
3.3.5. ifPhysAddress
3.3.5. ifPhysAddress
For an 802.5 interface, ifPhysAddress contains the interface's IEEE MAC address, stored as an octet string of length 6, in IEEE 802.1a "canonical" order, i.e., the Group Bit is positioned as the low-order bit (0x01) of the first octet.
802.5インタフェースに関しては、ifPhysAddressはIEEE 802.1aの「正準な」オーダーに長さ6の八重奏ストリングとして保存されたインタフェースのIEEE MACアドレスを含んでいます、すなわち、Group Bitが最初の八重奏の下位のビット(0×01)として置かれます。
3.3.6. ifType
3.3.6. ifType
The objects defined in this memo apply to each interface for which the ifType has the value:
このメモで定義されたオブジェクトはifTypeには値がある各インタフェースに適用されます:
iso88025-tokenRing(9)
iso88025-tokenRing(9)
4. Definitions
4. 定義
TOKENRING-MIB DEFINITIONS ::= BEGIN
TOKENRING-MIB定義:、:= 始まってください。
IMPORTS MODULE-IDENTITY, OBJECT-TYPE, OBJECT-IDENTITY, Counter32, Integer32 FROM SNMPv2-SMI transmission FROM RFC1213-MIB MacAddress,TimeStamp FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF;
IMPORTS MODULE-IDENTITY、OBJECT-TYPE、OBJECT-IDENTITY、Counter32、Integer32 FROM SNMPv2-SMIトランスミッションFROM RFC1213-MIB MacAddress、TimeStamp FROM SNMPv2-TC MODULE-COMPLIANCE、OBJECT-GROUP FROM SNMPv2-CONF。
dot5 MODULE-IDENTITY LAST-UPDATED "9410231150Z" ORGANIZATION "IETF Interfaces MIB Working Group" CONTACT-INFO " Keith McCloghrie
dot5 MODULE-IDENTITY LAST-UPDATED"9410231150Z"組織「IETFはMIB作業部会を連結する」コンタクトインフォメーション「キースMcCloghrie」
Postal: cisco Systems, Inc. 170 West Tasman Drive, San Jose, CA 95134-1706
郵便: 西タスマンDrive、コクチマスSystems Inc.170サンノゼ、カリフォルニア95134-1706
McCloghrie & Decker [Page 4] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[4ページ]RFC1743IEEE802.5MIB
US
米国
Phone: +1 408 526 5260 EMail: kzm@cisco.com" DESCRIPTION "The MIB module for IEEE Token Ring entities." ::= { transmission 9 }
以下に電話をしてください。 +1 5260年の408 526メール: " kzm@cisco.com "記述、「IEEE Token Ring実体のためのMIBモジュール。」 ::= トランスミッション9
-- The 802.5 Interface Table
-- 802.5インタフェーステーブル
-- This table contains state and parameter information which -- is specific to 802.5 interfaces. It is mandatory that -- systems having 802.5 interfaces implement this table in -- addition to the ifTable (see RFCs 1213 and 1573).
-- このテーブルが状態とパラメタ情報を含んでいる、どれ、--802.5のインタフェースへの詳細がそうである それは義務的です。それ--有802.5のインタフェースがこのテーブルを実装するシステム--ifTable(RFCs1213と1573を見る)への追加。
dot5Table OBJECT-TYPE SYNTAX SEQUENCE OF Dot5Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Token Ring interface parameters and state variables, one entry per 802.5 interface." ::= { dot5 1 }
「このテーブルはToken Ringインタフェース・パラメータと州の変数、802.5インタフェースあたり1つのエントリーに含む」dot5Table OBJECT-TYPE SYNTAX SEQUENCE OF Dot5Entryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述。 ::= dot5 1
dot5Entry OBJECT-TYPE SYNTAX Dot5Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of Token Ring status and parameter values for an 802.5 interface." INDEX { dot5IfIndex } ::= { dot5Table 1 }
「Token Ring状態とパラメタのリストは802.5インタフェースに評価する」dot5Entry OBJECT-TYPE SYNTAX Dot5Entryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述。 dot5IfIndexに索引をつけてください:、:= dot5Table1
Dot5Entry ::= SEQUENCE { dot5IfIndex Integer32, dot5Commands INTEGER, dot5RingStatus INTEGER, dot5RingState INTEGER, dot5RingOpenStatus INTEGER, dot5RingSpeed INTEGER, dot5UpStream MacAddress, dot5ActMonParticipate INTEGER, dot5Functional MacAddress, dot5LastBeaconSent TimeStamp }
Dot5Entry:、:= 系列dot5IfIndex Integer32、dot5Commands整数、dot5RingStatus整数、dot5RingState整数、dot5RingOpenStatus整数、dot5RingSpeed整数、dot5UpStream MacAddress、dot5ActMonParticipate整数、dot5Functional MacAddress、dot5LastBeaconSentタイムスタンプ
McCloghrie & Decker [Page 5] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[5ページ]RFC1743IEEE802.5MIB
dot5IfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object identifies the 802.5 interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object, defined in MIB-II for the same interface." ::= { dot5Entry 1 }
dot5IfIndex OBJECT-TYPE SYNTAX Integer32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述、「このオブジェクトの値はこのエントリーが経営情報を含む802.5インタフェースを特定します」。 「特定のインタフェースへのこのオブジェクトの値には、MIB-IIで同じインタフェースと定義されたifIndexオブジェクトと同じ値があります。」 ::= dot5Entry1
dot5Commands OBJECT-TYPE SYNTAX INTEGER { noop(1), open(2), reset(3), close(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "When this object is set to the value of open(2), the station should go into the open state. The progress and success of the open is given by the values of the objects dot5RingState and dot5RingOpenStatus. When this object is set to the value of reset(3), then the station should do a reset. On a reset, all MIB counters should retain their values, if possible. Other side affects are dependent on the hardware chip set. When this object is set to the value of close(4), the station should go into the stopped state by removing itself from the ring. Setting this object to a value of noop(1) has no effect. When read, this object always has a value of noop(1). The open(2) and close(4) values correspond to the up(1) and down(2) values of MIB-II's ifAdminStatus and ifOperStatus, i.e., the setting of ifAdminStatus and
dot5Commands OBJECT-TYPE SYNTAX INTEGER、noop(1)、戸外(2)、リセット(3)、マックス-ACCESSが「このオブジェクトは戸外(2)の値に設定されて、ステーションは開口状態に入るべきである」STATUSの現在の記述を読書して書く近い(4)。 オブジェクトのdot5RingStateとdot5RingOpenStatusの値で戸外の進歩と成功を与えます。 このオブジェクトがリセット(3)の値に設定されると、ステーションはリセットするべきです。 リセットのときに、可能であるなら、すべてのMIBカウンタがそれらの値を保有するはずです。 反対側感情はハードウェアチップ・セットに依存しています。 このオブジェクトが閉鎖(4)の値に設定されるとき、リングから立ち退くことによって、ステーションは止まっている状態に入るべきです。 noop(1)の値にこのオブジェクトを設定するのは効き目がありません。 読まれると、このオブジェクトには、noop(1)の値がいつもあります。 そして戸外(2)と近い(4)値が上(1)とすなわち、MIB-IIのifAdminStatusとifOperStatusの下に(2)値、ifAdminStatusの設定に対応している。
McCloghrie & Decker [Page 6] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[6ページ]RFC1743IEEE802.5MIB
dot5Commands affects the values of both dot5Commands and ifOperStatus." ::= { dot5Entry 2 }
「dot5Commandsはdot5CommandsとifOperStatusの両方の値に影響します。」 ::= dot5Entry2
dot5RingStatus OBJECT-TYPE SYNTAX INTEGER (0..262143) MAX-ACCESS read-only STATUS current DESCRIPTION "The current interface status which can be used to diagnose fluctuating problems that can occur on token rings, after a station has successfully been added to the ring. Before an open is completed, this object has the value for the 'no status' condition. The dot5RingState and dot5RingOpenStatus objects provide for debugging problems when the station can not even enter the ring. The object's value is a sum of values, one for each currently applicable condition. The following values are defined for various conditions:
dot5RingStatus OBJECT-TYPE SYNTAX INTEGER(0 .262143)のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述、「ステーションが首尾よくリングに加えられた後にトークンに起こることができる変動問題を診断するのに使用できる現在のインタフェース状態は鳴ります」。 戸外が完成する前に、このオブジェクトには、'状態がありません'状態のための値があります。 ステーションがリングを入れることさえできないとき、dot5RingStateとdot5RingOpenStatusオブジェクトはデバッグ問題に備えます。 オブジェクトの値は値の合計、それぞれの現在適切な状態あたり1つです。 以下の値は様々な状態のために定義されます:
0 = No Problems detected 32 = Ring Recovery 64 = Single Station 256 = Remove Received 512 = reserved 1024 = Auto-Removal Error 2048 = Lobe Wire Fault 4096 = Transmit Beacon 8192 = Soft Error 16384 = Hard Error 32768 = Signal Loss 131072 = no status, open not completed." ::= { dot5Entry 3 }
「0 = いいえProblems=単一の検出された32=リングRecovery64駅256の=は信号固い柔らかい2048=耳たぶWire Fault4096=が伝える予約された1024=自動Received512=Removal Error Beacon8192=Error16384=Error32768=Loss131072=状態を全く取り除きません、完成しなかった戸外。」 ::= dot5Entry3
dot5RingState OBJECT-TYPE SYNTAX INTEGER { opened(1), closed(2), opening(3), closing(4), openFailure(5), ringFailure(6) }
dot5RingStateオブジェクト・タイプ構文整数(1)、閉じた(2)を開いて、(3) openFailure(5)、(4)を閉じるringFailure(6)を開くこと。
McCloghrie & Decker [Page 7] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[7ページ]RFC1743IEEE802.5MIB
MAX-ACCESS read-only STATUS current DESCRIPTION "The current interface state with respect to entering or leaving the ring." ::= { dot5Entry 4 }
「現在のインタフェースはリングを入れるか、または残すことに関して述べる」マックス-ACCESSの書き込み禁止のSTATUSの現在の記述。 ::= dot5Entry4
dot5RingOpenStatus OBJECT-TYPE SYNTAX INTEGER { noOpen(1), -- no open attempted badParam(2), lobeFailed(3), signalLoss(4), insertionTimeout(5), ringFailed(6), beaconing(7), duplicateMAC(8), requestFailed(9), removeReceived(10), open(11) -- last open successful } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the success, or the reason for failure, of the station's most recent attempt to enter the ring." ::= { dot5Entry 5 }
dot5RingOpenStatus OBJECT-TYPE SYNTAX INTEGERのnoOpen(1)の、そして、最後の戸外のうまくいっている開いている試みられたbadParam(2)がない、lobeFailed(3)、signalLoss(4)、insertionTimeout(5)、ringFailed(6)が(7)、duplicateMAC(8)、requestFailed(9)、removeReceived(10)、戸外(11)に標識を設置して、マックス-ACCESS書き込み禁止STATUS現在の記述は「リングに上がるステーションの最新の試み成功、または失敗の理由を示これが反対するします」。 ::= dot5Entry5
dot5RingSpeed OBJECT-TYPE SYNTAX INTEGER { unknown(1), oneMegabit(2), fourMegabit(3), sixteenMegabit(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The ring-speed at the next insertion into the ring. Note that this may or may not be different to the current ring-speed which is given by MIB-II's ifSpeed. For interfaces which do not support changing ring-speed, dot5RingSpeed can only be set to its current value. When dot5RingSpeed has the value unknown(1), the ring's actual ring-speed is to be used."
dot5RingSpeed OBJECT-TYPE SYNTAX INTEGER、未知(1)、oneMegabit(2)、fourMegabit(3)、sixteenMegabit(4)、マックス-ACCESSは「リングへの次の挿入におけるリング速度」をSTATUSの現在の記述に読書して書きます。 これがMIB-IIのifSpeedによって与えられている現在のリング速度に異なるかもしれないことに注意してください。 リング速度を変えるのを支持しないインタフェースにおいて、dot5RingSpeedは現行価値に用意ができることができるだけです。 「リングの実際のリング速度はdot5RingSpeedに値の未知(1)があるとき、使用されていることです。」
McCloghrie & Decker [Page 8] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[8ページ]RFC1743IEEE802.5MIB
::= { dot5Entry 6 }
::= dot5Entry6
dot5UpStream OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC-address of the up stream neighbor station in the ring." ::= { dot5Entry 7 }
「上のMAC-アドレス流れの隣人はリングに配置する」dot5UpStream OBJECT-TYPE SYNTAX MacAddressのマックス-ACCESSの書き込み禁止のSTATUSの現在の記述。 ::= dot5Entry7
dot5ActMonParticipate OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "If this object has a value of true(1) then this interface will participate in the active monitor selection process. If the value is false(2) then it will not. Setting this object does not take effect until the next Active Monitor election, and might not take effect until the next time the interface is opened." ::= { dot5Entry 8 }
dot5ActMonParticipate OBJECT-TYPE SYNTAX INTEGER、本当の(1)、誤った(2)、マックス-ACCESSは「この物に本当の(1)の値があると、このインタフェースはアクティブなモニター選択の過程に参加すること」をSTATUSの現在の記述に読書して書きます。 値が誤った(2)であるなら、それはそうしないでしょう。 「この物を設定するのは、次のActive Monitor選挙まで効かないで、またインタフェースが次の時に開かれるまで、効かないかもしれません。」 ::= dot5Entry8
dot5Functional OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The bit mask of all Token Ring functional addresses for which this interface will accept frames." ::= { dot5Entry 9 }
dot5Functional OBJECT-TYPE SYNTAX MacAddressマックス-ACCESSは「このインタフェースがフレームを受け入れるすべてのToken Ring機能アドレスの噛み付いているマスク」をSTATUSの現在の記述に読書して書きます。 ::= dot5Entry9
dot5LastBeaconSent OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of MIB-II's sysUpTime object at which the local system last transmitted a Beacon frame on this interface." ::= { dot5Entry 10 }
dot5LastBeaconSent OBJECT-TYPE SYNTAX TimeStampのマックス-ACCESSの書き込み禁止のSTATUSの現在の記述、「ローカルシステムが最後にこのインタフェースでBeaconフレームを伝えたMIB-IIのsysUpTime物の値。」 ::= dot5Entry10
McCloghrie & Decker [Page 9] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[9ページ]RFC1743IEEE802.5MIB
-- The 802.5 Statistics Table
-- 802.5統計テーブル
-- This table contains statistics and error counter which are -- specific to 802.5 interfaces. It is mandatory that systems -- having 802.5 interfaces implement this table.
-- このテーブルはそうする統計と誤りカウンタを含んでいます--802.5のインタフェースに、特定です。 802.5が連結するシステム--有がこのテーブルを実行するのは、義務的です。
dot5StatsTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot5StatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing Token Ring statistics, one entry per 802.5 interface. All the statistics are defined using the syntax Counter32 as 32-bit wrap around counters. Thus, if an interface's hardware maintains these statistics in 16-bit counters, then the agent must read the hardware's counters frequently enough to prevent loss of significance, in order to maintain 32-bit counters in software." ::= { dot5 2 }
「802.5インタフェース単位でToken Ring統計、あるエントリーを含んでいて、Aはテーブルの上に置く」dot5StatsTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot5StatsEntryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述。 すべての統計が、32ビットの包装としてカウンタの周りで構文Counter32を使用することで定義されます。 「その結果、インタフェースのハードウェアが16ビットのカウンタでこれらの統計を維持するなら、エージェントは意味の損失を防ぐことができるくらいの頻繁にハードウェアのカウンタを読まなければなりません、ソフトウェアの32ビットのカウンタを維持するために。」 ::= dot5 2
dot5StatsEntry OBJECT-TYPE SYNTAX Dot5StatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry contains the 802.5 statistics for a particular interface." INDEX { dot5StatsIfIndex } ::= { dot5StatsTable 1 }
dot5StatsEntry OBJECT-TYPE SYNTAX Dot5StatsEntryのマックス-ACCESSのアクセスしやすくないSTATUS現在の記述、「エントリーは特定のインタフェースへの802.5の統計を含んでいます」。 dot5StatsIfIndexに索引をつけてください:、:= dot5StatsTable1
Dot5StatsEntry ::= SEQUENCE { dot5StatsIfIndex Integer32, dot5StatsLineErrors Counter32, dot5StatsBurstErrors Counter32, dot5StatsACErrors Counter32, dot5StatsAbortTransErrors Counter32, dot5StatsInternalErrors Counter32, dot5StatsLostFrameErrors Counter32, dot5StatsReceiveCongestions Counter32, dot5StatsFrameCopiedErrors Counter32, dot5StatsTokenErrors Counter32, dot5StatsSoftErrors Counter32, dot5StatsHardErrors Counter32, dot5StatsSignalLoss Counter32,
Dot5StatsEntry:、:= 系列、dot5StatsIfIndex Integer32、dot5StatsLineErrors Counter32、dot5StatsBurstErrors Counter32、dot5StatsACErrors Counter32、dot5StatsAbortTransErrors Counter32、dot5StatsInternalErrors Counter32、dot5StatsLostFrameErrors Counter32、dot5StatsReceiveCongestions Counter32、dot5StatsFrameCopiedErrors Counter32、dot5StatsTokenErrors Counter32、dot5StatsSoftErrors Counter32、dot5StatsHardErrors Counter32、dot5StatsSignalLoss Counter32
McCloghrie & Decker [Page 10] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[10ページ]RFC1743IEEE802.5MIB
dot5StatsTransmitBeacons Counter32, dot5StatsRecoverys Counter32, dot5StatsLobeWires Counter32, dot5StatsRemoves Counter32, dot5StatsSingles Counter32, dot5StatsFreqErrors Counter32 }
dot5StatsTransmitBeacons Counter32、dot5StatsRecoverys Counter32、dot5StatsLobeWires Counter32、dot5StatsRemoves Counter32、dot5StatsSingles Counter32、dot5StatsFreqErrors Counter32
dot5StatsIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object identifies the 802.5 interface for which this entry contains management information. The value of this object for a particular interface has the same value as MIB-II's ifIndex object for the same interface." ::= { dot5StatsEntry 1 }
dot5StatsIfIndex OBJECT-TYPE SYNTAX Integer32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述、「この物の値はこのエントリーが経営情報を含む802.5インタフェースを特定します」。 「特定のインタフェースへのこの物の値には、同じインタフェースへのMIB-IIのifIndex物と同じ値があります。」 ::= dot5StatsEntry1
dot5StatsLineErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter is incremented when a frame or token is copied or repeated by a station, the E bit is zero in the frame or token and one of the following conditions exists: 1) there is a non-data bit (J or K bit) between the SD and the ED of the frame or token, or 2) there is an FCS error in the frame." ::= { dot5StatsEntry 2 }
dot5StatsLineErrors OBJECT-TYPE SYNTAX Counter32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述、「このカウンタは、フレームか象徴がコピーされるとき、増加されるか、またはステーションによって繰り返されます、そして、Eビットはフレームか象徴のゼロです、そして、以下の条件の1つは存在しています」。 「1) フレームか象徴のサウスダコタとEDの間には、非データ・ビット(JかKビット)があるか、そこの2は)フレームのFCS誤りです。」 ::= dot5StatsEntry2
dot5StatsBurstErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter is incremented when a station detects the absence of transitions for five half-bit timers (burst-five error)." ::= { dot5StatsEntry 3 }
dot5StatsBurstErrors OBJECT-TYPE SYNTAX Counter32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述、「ステーションが5個の半ビットタイマ(バースト5誤り)のための変遷の欠如を検出すると、このカウンタは増加されています」。 ::= dot5StatsEntry3
McCloghrie & Decker [Page 11] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[11ページ]RFC1743IEEE802.5MIB
dot5StatsACErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter is incremented when a station receives an AMP or SMP frame in which A is equal to C is equal to 0, and then receives another SMP frame with A is equal to C is equal to 0 without first receiving an AMP frame. It denotes a station that cannot set the AC bits properly." ::= { dot5StatsEntry 4 }
dot5StatsACErrors OBJECT-TYPE SYNTAX Counter32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述、「aステーションがAMPを受けるか、またはAがCの同輩が0に堪えるということであり、次にAと共に別のSMPフレームを受けるSMPフレームがCと等しいときに、最初にAMPフレームを受けないで、増加されたこのカウンタは0と等しいです」。 「適切に交流ビットを設定できないステーションを指示します。」 ::= dot5StatsEntry4
dot5StatsAbortTransErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter is incremented when a station transmits an abort delimiter while transmitting." ::= { dot5StatsEntry 5 }
dot5StatsAbortTransErrors OBJECT-TYPE SYNTAX Counter32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述、「ステーションが伝わっている間アボートデリミタを送信するとき、このカウンタは増加されています」。 ::= dot5StatsEntry5
dot5StatsInternalErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter is incremented when a station recognizes an internal error." ::= { dot5StatsEntry 6 }
dot5StatsInternalErrors OBJECT-TYPE SYNTAX Counter32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述、「ステーションが内部エラーを認識すると、このカウンタは増加されています」。 ::= dot5StatsEntry6
dot5StatsLostFrameErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter is incremented when a station is transmitting and its TRR timer expires. This condition denotes a condition where a transmitting station in strip mode does not receive the trailer of the frame before the TRR timer goes off." ::= { dot5StatsEntry 7 }
「ステーションが伝わっているとき増加されたこのカウンタとそのTRRタイマは吐き出す」dot5StatsLostFrameErrors OBJECT-TYPE SYNTAX Counter32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述。 「この状態はTRRタイマが発射される前に片モードによる送信所がフレームのトレーラを受けない状態を指示します。」 ::= dot5StatsEntry7
McCloghrie & Decker [Page 12] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[12ページ]RFC1743IEEE802.5MIB
dot5StatsReceiveCongestions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter is incremented when a station recognizes a frame addressed to its specific address, but has no available buffer space indicating that the station is congested." ::= { dot5StatsEntry 8 }
「特定のアドレスに記述しますがステーションはバッファ領域表示ですが、充血して、利用可能に持ステーションであるときに増加されたこのカウンタがフレームを認めるていない」dot5StatsReceiveCongestions OBJECT-TYPE SYNTAX Counter32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述。 ::= dot5StatsEntry8
dot5StatsFrameCopiedErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter is incremented when a station recognizes a frame addressed to its specific address and detects that the FS field A bits are set to 1 indicating a possible line hit or duplicate address." ::= { dot5StatsEntry 9 }
dot5StatsFrameCopiedErrors OBJECT-TYPE SYNTAX Counter32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述、「このカウンタによるステーションが特定のアドレスに記述されたフレームを認識して、それを検出すると増加されて、FS分野Aビットが可能な回線時時断か写しアドレスを示す1に設定されるということです」。 ::= dot5StatsEntry9
dot5StatsTokenErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter is incremented when a station acting as the active monitor recognizes an error condition that needs a token transmitted." ::= { dot5StatsEntry 10 }
dot5StatsTokenErrors OBJECT-TYPE SYNTAX Counter32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述、「活発なモニターが象徴を必要とするエラー条件を認めるので行動するステーションが伝わったとき、このカウンタは増加されています」。 ::= dot5StatsEntry10
dot5StatsSoftErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Soft Errors the interface has detected. It directly corresponds to the number of Report Error MAC frames that this interface has transmitted. Soft Errors are those which are recoverable by the MAC layer protocols." ::= { dot5StatsEntry 11 }
dot5StatsSoftErrors OBJECT-TYPE SYNTAX Counter32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述、「インタフェースが検出したSoft Errorsの数。」 直接、このインタフェースが伝わったのはReport Error MACフレームの数に対応しています。 「柔らかいErrorsはMAC層のプロトコルで回復可能なものです。」 ::= dot5StatsEntry11
McCloghrie & Decker [Page 13] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[13ページ]RFC1743IEEE802.5MIB
dot5StatsHardErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this interface has detected an immediately recoverable fatal error. It denotes the number of times this interface is either transmitting or receiving beacon MAC frames." ::= { dot5StatsEntry 12 }
dot5StatsHardErrors OBJECT-TYPE SYNTAX Counter32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述、「このインタフェースがすぐに回復可能な致命的な誤りを検出したという回の数。」 「このインタフェースが標識MACフレームを伝えるか、または受けているという回の数を指示します。」 ::= dot5StatsEntry12
dot5StatsSignalLoss OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this interface has detected the loss of signal condition from the ring." ::= { dot5StatsEntry 13 }
dot5StatsSignalLoss OBJECT-TYPE SYNTAX Counter32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述、「このインタフェースが損失を検出した回数はリングからの状態を示します」。 ::= dot5StatsEntry13
dot5StatsTransmitBeacons OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this interface has transmitted a beacon frame." ::= { dot5StatsEntry 14 }
dot5StatsTransmitBeacons OBJECT-TYPE SYNTAX Counter32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述、「このインタフェースが標識フレームを伝えたという回の数。」 ::= dot5StatsEntry14
dot5StatsRecoverys OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Claim Token MAC frames received or transmitted after the interface has received a Ring Purge MAC frame. This counter signifies the number of times the ring has been purged and is being recovered back into a normal operating state." ::= { dot5StatsEntry 15 }
「インタフェースがRing Purge MACフレームを受けた後に、クレームToken MACフレームの数は、受けたか、または伝えた」dot5StatsRecoverys OBJECT-TYPE SYNTAX Counter32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述。 「このカウンタはリングが掃除されて、正常な作動状態に回収して戻されているという回の数を意味します。」 ::= dot5StatsEntry15
dot5StatsLobeWires OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only
dot5StatsLobeWires OBJECT-TYPE SYNTAX Counter32マックス-ACCESS書き込み禁止
McCloghrie & Decker [Page 14] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[14ページ]RFC1743IEEE802.5MIB
STATUS current DESCRIPTION "The number of times the interface has detected an open or short circuit in the lobe data path. The adapter will be closed and dot5RingState will signify this condition." ::= { dot5StatsEntry 16 }
STATUSの現在の記述、「インタフェースが耳たぶデータ経路の開いているか短いサーキットを検出したという回の数。」 「アダプターは閉じられるでしょう、そして、dot5RingStateはこの状態を意味するでしょう。」 ::= dot5StatsEntry16
dot5StatsRemoves OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the interface has received a Remove Ring Station MAC frame request. When this frame is received the interface will enter the close state and dot5RingState will signify this condition." ::= { dot5StatsEntry 17 }
dot5StatsRemoves OBJECT-TYPE SYNTAX Counter32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述、「インタフェースがRemove Ring駅のMACを受けたという回の数は要求を縁どっています」。 「このフレームが受け取られているとき、インタフェースは近い状態に入るでしょう、そして、dot5RingStateはこの状態を意味するでしょう。」 ::= dot5StatsEntry17
dot5StatsSingles OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the interface has sensed that it is the only station on the ring. This will happen if the interface is the first one up on a ring, or if there is a hardware problem." ::= { dot5StatsEntry 18 }
dot5StatsSingles OBJECT-TYPE SYNTAX Counter32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述、「それがリングの上の唯一のステーションであるというインタフェースが感じた回の数。」 「インタフェースがリングで上がっている最初のものである、またはハードウェア問題があると、これは起こるでしょう。」 ::= dot5StatsEntry18
dot5StatsFreqErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the interface has detected that the frequency of the incoming signal differs from the expected frequency by more than that specified by the IEEE 802.5 standard." ::= { dot5StatsEntry 19 }
dot5StatsFreqErrors OBJECT-TYPE SYNTAX Counter32のマックス-ACCESSの書き込み禁止のSTATUSの現在の記述、「入って来る信号の頻度がそれ以上で期待度数と異なっているというインタフェースが検出した回の数はIEEE802.5規格で指定しました」。 ::= dot5StatsEntry19
McCloghrie & Decker [Page 15] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[15ページ]RFC1743IEEE802.5MIB
-- The Timer Table
-- タイマテーブル
-- This group contains the values of timers for 802.5 -- interfaces. This table is obsolete, but its definition -- is retained here for backwards compatibility.
-- このグループは802.5のためのタイマの値を含みます--インタフェース。 しかし、このテーブルは時代遅れです。定義--ここで、遅れている互換性のために、保有されます。
dot5TimerTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot5TimerEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "This table contains Token Ring interface timer values, one entry per 802.5 interface." ::= { dot5 5 }
dot5TimerTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot5TimerEntryのマックス-ACCESSのアクセスしやすくないSTATUSは「このテーブルはToken Ringインタフェースタイマ値、802.5インタフェースあたり1つのエントリーに含む」記述を時代遅れにします。 ::= dot5 5
dot5TimerEntry OBJECT-TYPE SYNTAX Dot5TimerEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "A list of Token Ring timer values for an 802.5 interface." INDEX { dot5TimerIfIndex } ::= { dot5TimerTable 1 }
dot5TimerEntry OBJECT-TYPE SYNTAX Dot5TimerEntryのマックス-ACCESSのアクセスしやすくないSTATUSは「Token Ringタイマのリストは802.5インタフェースに評価する」記述を時代遅れにします。 dot5TimerIfIndexに索引をつけてください:、:= dot5TimerTable1
Dot5TimerEntry ::= SEQUENCE { dot5TimerIfIndex Integer32, dot5TimerReturnRepeat Integer32, dot5TimerHolding Integer32, dot5TimerQueuePDU Integer32, dot5TimerValidTransmit Integer32, dot5TimerNoToken Integer32, dot5TimerActiveMon Integer32, dot5TimerStandbyMon Integer32, dot5TimerErrorReport Integer32, dot5TimerBeaconTransmit Integer32, dot5TimerBeaconReceive Integer32 }
Dot5TimerEntry:、:= 系列dot5TimerIfIndex Integer32、dot5TimerReturnRepeat Integer32、dot5TimerHolding Integer32、dot5TimerQueuePDU Integer32、dot5TimerValidTransmit Integer32、dot5TimerNoToken Integer32、dot5TimerActiveMon Integer32、dot5TimerStandbyMon Integer32、dot5TimerErrorReport Integer32、dot5TimerBeaconTransmit Integer32、dot5TimerBeaconReceive Integer32
dot5TimerIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The value of this object identifies the 802.5 interface for which this entry contains timer values. The value of
dot5TimerIfIndex OBJECT-TYPE SYNTAX Integer32マックス-ACCESS書き込み禁止STATUSは記述を時代遅れにします。「このオブジェクトの値はこのエントリーがタイマ値を含む802.5インタフェースを特定します」。 価値
McCloghrie & Decker [Page 16] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[16ページ]RFC1743IEEE802.5MIB
this object for a particular interface has the same value as MIB-II's ifIndex object for the same interface." ::= { dot5TimerEntry 1 }
「特定のインタフェースへのこのオブジェクトには、同じインタフェースへのMIB-IIのifIndexオブジェクトと同じ値があります。」 ::= dot5TimerEntry1
dot5TimerReturnRepeat OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The time-out value used to ensure the interface will return to Repeat State, in units of 100 micro-seconds. The value should be greater than the maximum ring latency." ::= { dot5TimerEntry 2 }
dot5TimerReturnRepeat OBJECT-TYPE SYNTAX Integer32マックス-ACCESS書き込み禁止STATUSは「タイムアウト値はインタフェースが100マイクロセカンドのユニットでRepeat州に戻るのを保証するのに使用した」記述を時代遅れにします。 「値は最大のリング遅延より大きいはずです。」 ::= dot5TimerEntry2
dot5TimerHolding OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "Maximum period of time a station is permitted to transmit frames after capturing a token, in units of 100 micro-seconds." ::= { dot5TimerEntry 3 }
dot5TimerHolding OBJECT-TYPE SYNTAX Integer32マックス-ACCESS書き込み禁止STATUSは「100マイクロセカンドのステーションがユニットのトークンを得た後のフレームを伝えることが許可されている最大の期間」のときに記述を時代遅れにします。 ::= dot5TimerEntry3
dot5TimerQueuePDU OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The time-out value for enqueuing of an SMP PDU after reception of an AMP or SMP frame in which the A and C bits were equal to 0, in units of 100 micro-seconds." ::= { dot5TimerEntry 4 }
dot5TimerQueuePDU OBJECT-TYPE SYNTAX Integer32マックス-ACCESS書き込み禁止STATUSは「タイムアウトはAとCビットが100マイクロセカンドのユニットの0と等しかったAMPかSMPフレームのレセプションの後にSMP PDUを待ち行列に入れるために評価する」記述を時代遅れにします。 ::= dot5TimerEntry4
dot5TimerValidTransmit OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The time-out value used by the active monitor to detect the absence of valid transmissions, in units of 100 micro-seconds."
dot5TimerValidTransmit OBJECT-TYPE SYNTAX Integer32マックス-ACCESS書き込み禁止STATUSは「タイムアウト値は100マイクロセカンドのユニットにおける、有効なトランスミッションの欠如を検出するのに活発なモニターで使用した」記述を時代遅れにします。
McCloghrie & Decker [Page 17] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[17ページ]RFC1743IEEE802.5MIB
::= { dot5TimerEntry 5 }
::= dot5TimerEntry5
dot5TimerNoToken OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The time-out value used to recover from various-related error situations. If N is the maximum number of stations on the ring, the value of this timer is normally: dot5TimerReturnRepeat + N*dot5TimerHolding." ::= { dot5TimerEntry 6 }
dot5TimerNoToken OBJECT-TYPE SYNTAX Integer32マックス-ACCESS書き込み禁止STATUSは「タイムアウト値は以前はさまざまな関連のエラー状態からよく回復していた」記述を時代遅れにします。 Nがリングの上のステーションの最大数であるなら、通常、このタイマの値は以下の通りです。 「dot5TimerReturnRepeat+N*dot5TimerHolding。」 ::= dot5TimerEntry6
dot5TimerActiveMon OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The time-out value used by the active monitor to stimulate the enqueuing of an AMP PDU for transmission, in units of 100 micro-seconds." ::= { dot5TimerEntry 7 }
dot5TimerActiveMon OBJECT-TYPE SYNTAX Integer32マックス-ACCESS書き込み禁止STATUSは「タイムアウト値はトランスミッションのためにAMP PDUを待ち行列に入れることを刺激するのに100マイクロセカンドのユニットで活発なモニターで使用した」記述を時代遅れにします。 ::= dot5TimerEntry7
dot5TimerStandbyMon OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The time-out value used by the stand-by monitors to ensure that there is an active monitor on the ring and to detect a continuous stream of tokens, in units of 100 micro-seconds." ::= { dot5TimerEntry 8 }
dot5TimerStandbyMon OBJECT-TYPE SYNTAX Integer32マックス-ACCESS書き込み禁止STATUSは「タイムアウト値はリングの上に活発なモニターがあるのを保証して、トークンの連続したストリームを検出するのに100マイクロセカンドのユニットで予備モニターで使用した」記述を時代遅れにします。 ::= dot5TimerEntry8
dot5TimerErrorReport OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The time-out value which determines how often a station shall send a Report Error MAC frame to report its error counters, in units of 100 micro-seconds." ::= { dot5TimerEntry 9 }
dot5TimerErrorReport OBJECT-TYPE SYNTAX Integer32マックス-ACCESS書き込み禁止STATUSは「100マイクロセカンドのユニットでは打ち返どれくらいの頻度でステーションがReport Error MACフレームを送るだろうことを決定するタイムアウト値が誤りを報告するする」記述を時代遅れにします。 ::= dot5TimerEntry9
McCloghrie & Decker [Page 18] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[18ページ]RFC1743IEEE802.5MIB
dot5TimerBeaconTransmit OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The time-out value which determines how long a station shall remain in the state of transmitting Beacon frames before entering the Bypass state, in units of 100 micro-seconds." ::= { dot5TimerEntry 10 }
dot5TimerBeaconTransmit OBJECT-TYPE SYNTAX Integer32マックス-ACCESS書き込み禁止STATUSは「タイムアウトは100マイクロセカンドのユニットでBypass状態に入る前にBeaconフレームを伝えながら、どれくらい長いステーションが州に残るかを決定するものを評価する」記述を時代遅れにします。 ::= dot5TimerEntry10
dot5TimerBeaconReceive OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The time-out value which determines how long a station shall receive Beacon frames from its downstream neighbor before entering the Bypass state, in units of 100 micro-seconds." ::= { dot5TimerEntry 11 }
dot5TimerBeaconReceive OBJECT-TYPE SYNTAX Integer32マックス-ACCESS書き込み禁止STATUSは「タイムアウトが100マイクロセカンドのユニットでBypass状態に入りながらどれくらい長いステーションが川下の隣人からBeaconフレームを受けるだろうかを決定するものを評価する前」記述を時代遅れにします。 ::= dot5TimerEntry11
-- 802.5 Interface Tests
-- 802.5 インタフェーステスト
dot5Tests OBJECT IDENTIFIER ::= { dot5 3 }
dot5Testsオブジェクト識別子:、:= dot5 3
-- RFC 1573 defines the ifTestTable, through which a -- network manager can instruct an agent to test an interface -- for various faults. A test to be performed is identified -- as an OBJECT IDENTIFIER.
-- RFC1573はifTestTableを定義します、どのaを通して--ネットワークマネージャは、様々な欠点がないかどうかインタフェースをテストするようエージェントに命令できるか。 実行されるべきテストは特定されます--OBJECT IDENTIFIERとして。
-- The Insert Function test
-- Insert Functionテスト
dot5TestInsertFunc OBJECT-IDENTITY STATUS current DESCRIPTION "Invoking this test causes the station to test the insert ring logic of the hardware if the station's lobe media cable is connected to a wiring concentrator. Note that this command inserts the station into the network, and thus, could cause problems if the station is connected to a operational network." ::= { dot5Tests 1 }
「ステーションの耳たぶメディアケーブルが配線集中装置に接続されるなら、このテストを呼び出すのはステーションをハードウェアのインサート・リング論理をテストさせる」dot5TestInsertFunc OBJECT-IDENTITY STATUSの現在の記述。 「これが命令するというメモは、ステーションをネットワークに挿入して、その結果、ステーションが操作上のネットワークにつなげられるなら、問題を起こすかもしれません。」 ::= dot5Tests1
McCloghrie & Decker [Page 19] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[19ページ]RFC1743IEEE802.5MIB
-- The Full-Duplex Loop Back test
-- Full-デュプレックスLoop Backテスト
dot5TestFullDuplexLoopBack OBJECT-IDENTITY STATUS current DESCRIPTION "Invoking this test on a 802.5 interface causes the interface to check the path from memory through the chip set's internal logic and back to memory, thus checking the proper functioning of the system's interface to the chip set." ::= { dot5Tests 2 }
「802.5インタフェースにこのテストを呼び出すのはインタフェースを経路をメモリに行き帰りメモリから内部のチップ・セットの論理までチェックさせて、その結果、システムのインタフェースの適切な機能をチップ・セットにチェックします」dot5TestFullDuplexLoopBack OBJECT-IDENTITY STATUSの現在の記述。 ::= dot5Tests2
-- 802.5 Hardware Chip Sets
-- 802.5 ハードウェアチップ・セット
-- RFC 1229 specified an object, ifExtnsChipSet, with the -- syntax of OBJECT IDENTIFIER, to identify the hardware -- chip set in use by an interface. RFC 1573 obsoletes -- the use of ifExtnsChipSet. However, the following -- definitions are retained for backwards compatibility.
-- RFC1229がオブジェクト、ifExtnsChipSetを指定した、--OBJECT IDENTIFIERの構文、ハードウェア--欠けるのを特定するのがインタフェースのそばに使用中にセットしました。 RFC1573が時代遅れにする、--ifExtnsChipSetの使用。 しかしながら、以下--定義は遅れている互換性のために保有されます。
dot5ChipSets OBJECT IDENTIFIER ::= { dot5 4 }
dot5ChipSetsオブジェクト識別子:、:= dot5 4
dot5ChipSetIBM16 OBJECT-IDENTITY STATUS current DESCRIPTION "IBM's 16/4 Mbs chip set." ::= { dot5ChipSets 1 }
「設定されて、IBMの16/4Mbsが欠く」dot5ChipSetIBM16 OBJECT-IDENTITY STATUSの現在の記述。 ::= dot5ChipSets1
dot5ChipSetTItms380 OBJECT-IDENTITY STATUS current DESCRIPTION "Texas Instruments' TMS 380 4Mbs chip-set" ::= { dot5ChipSets 2 }
「米国テキサス・インスツルメンツ社のTMS380 4Mbsはチップで設定する」dot5ChipSetTItms380 OBJECT-IDENTITY STATUSの現在の記述:、:= dot5ChipSets2
dot5ChipSetTItms380c16 OBJECT-IDENTITY STATUS current DESCRIPTION "Texas Instruments' TMS 380C16 16/4 Mbs chip-set" ::= { dot5ChipSets 3 }
「米国テキサス・インスツルメンツ社のTMS 380C16 16/4 Mbsはチップで設定する」dot5ChipSetTItms380c16 OBJECT-IDENTITY STATUSの現在の記述:、:= dot5ChipSets3
McCloghrie & Decker [Page 20] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[20ページ]RFC1743IEEE802.5MIB
-- conformance information
-- 順応情報
dot5Conformance OBJECT IDENTIFIER ::= { dot5 5 }
dot5Conformanceオブジェクト識別子:、:= dot5 5
dot5Groups OBJECT IDENTIFIER ::= { dot5Conformance 1 } dot5Compliances OBJECT IDENTIFIER ::= { dot5Conformance 2 }
dot5Groupsオブジェクト識別子:、:= dot5Conformance1dot5Compliancesオブジェクト識別子:、:= dot5Conformance2
-- compliance statements
-- 承諾声明
dot5Compliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMPv2 entities which implement the IEEE 802.5 MIB."
dot5Compliance MODULE-COMPLIANCE STATUSの現在の記述、「IEEE802.5MIBを実装するSNMPv2実体のための承諾声明。」
MODULE -- this module MANDATORY-GROUPS { dot5StateGroup, dot5StatsGroup }
MODULE--このモジュールMANDATORY-GROUPSdot5StateGroup、dot5StatsGroup
OBJECT dot5ActMonParticipate MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT dot5ActMonParticipate MIN-ACCESS書き込み禁止記述、「書く、アクセスは必要でない、」
OBJECT dot5Functional MIN-ACCESS read-only DESCRIPTION "Write access is not required."
OBJECT dot5Functional MIN-ACCESS書き込み禁止記述、「書く、アクセスは必要でない、」
::= { dot5Compliances 1 }
::= dot5Compliances1
-- units of conformance
-- ユニットの順応
dot5StateGroup OBJECT-GROUP OBJECTS { dot5Commands, dot5RingStatus, dot5RingState, dot5RingOpenStatus, dot5RingSpeed, dot5UpStream, dot5ActMonParticipate, dot5Functional, dot5LastBeaconSent } STATUS current DESCRIPTION "A collection of objects providing state information and parameters for IEEE 802.5 interfaces." ::= { dot5Groups 1 }
dot5StateGroup OBJECT-GROUP OBJECTS、dot5Commands、dot5RingStatus、dot5RingState、dot5RingOpenStatus、dot5RingSpeed、dot5UpStream、dot5ActMonParticipate、dot5Functional、dot5LastBeaconSent、「州の情報を提供するオブジェクトの収集とIEEE802.5のためのパラメタは連結する」STATUSの現在の記述。 ::= dot5Groups1
dot5StatsGroup OBJECT-GROUP OBJECTS { dot5StatsLineErrors, dot5StatsBurstErrors,
dot5StatsGroupオブジェクト群対象、dot5StatsLineErrors、dot5StatsBurstErrors
McCloghrie & Decker [Page 21] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[21ページ]RFC1743IEEE802.5MIB
dot5StatsACErrors, dot5StatsAbortTransErrors, dot5StatsInternalErrors, dot5StatsLostFrameErrors, dot5StatsReceiveCongestions, dot5StatsFrameCopiedErrors, dot5StatsTokenErrors, dot5StatsSoftErrors, dot5StatsHardErrors, dot5StatsSignalLoss, dot5StatsTransmitBeacons, dot5StatsRecoverys, dot5StatsLobeWires, dot5StatsRemoves, dot5StatsSingles, dot5StatsFreqErrors } STATUS current DESCRIPTION "A collection of objects providing statistics for IEEE 802.5 interfaces." ::= { dot5Groups 2 }
dot5StatsACErrors、dot5StatsAbortTransErrors、dot5StatsInternalErrors、dot5StatsLostFrameErrors、dot5StatsReceiveCongestions、dot5StatsFrameCopiedErrors、dot5StatsTokenErrors、dot5StatsSoftErrors、dot5StatsHardErrors、dot5StatsSignalLoss、dot5StatsTransmitBeacons、dot5StatsRecoverys、dot5StatsLobeWires、dot5StatsRemoves、dot5StatsSingles、dot5StatsFreqErrors 「オブジェクトがIEEE802.5に統計を供給する収集は連結する」STATUSの現在の記述。 ::= dot5Groups2
END
終わり
McCloghrie & Decker [Page 22] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[22ページ]RFC1743IEEE802.5MIB
5. Acknowledgements
5. 承認
The changes from RFC 1231 are the result of discussions on the IETF's snmp mailing-list and in the Interfaces MIB Working Group.
RFC1231からの変化はIETFのsnmpメーリングリストとInterfaces MIB作業部会で、議論の結果です。
6. References
6. 参照
[1] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Structure of Management Information for version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1442, SNMP Research,Inc., Hughes LAN Systems, Dover Beach Consulting, Inc., Carnegie Mellon University, April 1993.
[1]ケース、J.、McCloghrie、K.、ローズ、M.、およびS.Waldbusser、「Simple Network Managementプロトコル(SNMPv2)のバージョン2のためのManagement情報の構造」、RFC1442、SNMP Research、株式会社、ヒューズLAN Systems、ドーヴァービーチConsulting Inc.、カーネギーメロン大学(1993年4月)。
[2] McCloghrie, K., and M. Rose, Editors, "Management Information Base for Network Management of TCP/IP-based internets: MIB-II", STD 17, RFC 1213, Hughes LAN Systems, Performance Systems International, March 1991.
[2] McCloghrie、K.とM.ローズ、エディターズ、「TCP/IPベースのインターネットのNetwork Managementのための管理Information基地:」 「MIB-II」、STD17、RFC1213、ヒューズLANシステム、国際言語運用機構、1991年3月。
[3] Galvin, J., and K. McCloghrie, "Administrative Model for version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1445, Trusted Information Systems, Hughes LAN Systems, April 1993.
[3] ガルビン、J.、およびK.McCloghrie、「Simple Network Managementプロトコル(SNMPv2)のバージョン2のための管理Model」、RFC1445、Trusted情報システム、ヒューズLAN Systems(1993年4月)。
[4] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol Operations for version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1448, SNMP Research,Inc., Hughes LAN Systems, Dover Beach Consulting, Inc., Carnegie Mellon University, April 1993.
[4] ケース、J.、McCloghrie(K.、ローズ、M.、およびS.Waldbusser)は「Simple Network Managementプロトコル(SNMPv2)のバージョン2のためにOperationsについて議定書の中で述べます」、RFC1448、SNMP Research、株式会社、ヒューズLAN Systems、ドーヴァービーチConsulting Inc.、カーネギーメロン大学、1993年4月。
[5] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Textual Conventions for version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1443, SNMP Research,Inc., Hughes LAN Systems, Dover Beach Consulting, Inc., Carnegie Mellon University, April 1993.
[5]ケース、J.、McCloghrie、K.、ローズ、M.、およびS.Waldbusser、「Simple Network Managementプロトコル(SNMPv2)のバージョン2のための原文のConventions」、RFC1443、SNMP Research、株式会社、ヒューズLAN Systems、ドーヴァービーチConsulting Inc.、カーネギーメロン大学(1993年4月)。
[6] McCloghrie, K., and F. Kastenholz, "Evolution of the Interfaces Group of MIB-II", RFC 1573, Hughes LAN Systems, FTP Software, Jan 1994
[6]McCloghrie、K.、およびF.Kastenholz、「MIB-IIのインタフェースグループの発展」、RFC1573、ヒューズLANシステム、FTPソフトウェア、1994年1月
[7] Institute of Electrical and Electronic Engineers, "Token Ring Access Method and Physical Layer Specifications", IEEE Standard 802.5-1989, 1989.
[7]電気電子学会、「トークンリングはメソッドと物理的な層の仕様にアクセスする」IEEE規格802.5-1989、1989。
McCloghrie & Decker [Page 23] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[23ページ]RFC1743IEEE802.5MIB
APPENDIX A - Changes from RFC 1231
付録A--RFC1231からの変化
This memo has the following differences from RFC 1231:
このメモには、RFC1231からの以下の違いがあります:
(1) This memo is formatted using the SNMPv2 SMI.
(1) このメモは、SNMPv2 SMIを使用することでフォーマットされます。
(2) The relationship of the "open" and "close" states of dot5Commands to the value of ifAdminStatus has been clarified. In particular, the setting of one affects the value of the other.
(2) ifAdminStatusの値へのdot5Commandsの「開いてい」て「近い」州の関係ははっきりさせられました。 特に、1の設定はもう片方の値に影響します。
(3) The relationship dot5RingSpeed and ifSpeed has been clarified. In particular, ifSpeed indicates the current ring-speed; dot5RingSpeed indicates the ring-speed at the next insertion into the ring. If the interface doesn't support changing ring-speed, then dot5RingSpeed can only be set to its current value. When dot5RingSpeed has the value 'unknown(1)', the ring-speed is to be set to the ring's actual ring-speed.
(3) 関係のdot5RingSpeedとifSpeedははっきりさせられました。 特に、ifSpeedは現在のリング速度を示します。 dot5RingSpeedは次の挿入のときにリング速度をリングに示します。 インタフェースが変化リング速度をサポートしないなら、dot5RingSpeedは現行価値に用意ができることができるだけです。 dot5RingSpeedに値の'未知(1)'があると、リング速度はリングの実際のリング速度に設定されることです。
(4) Write-access to dot5ActMonParticipate is not required, and a change to the value of dot5ActMonParticipate does not take effect until the next Active Monitor election.
(4) アクセスを書いているdot5ActMonParticipateは必要ではありません、そして、dot5ActMonParticipateの値への変化は次のActive Monitor選挙まで効きません。
(5) Write-access to dot5Functional is not required.
(5) アクセスを書いているdot5Functionalは必要ではありません。
(6) A new object, dot5LastBeaconSent has been defined to contain the timestamp of the last beacon frame sent.
(6) 新しいオブジェクトであり、dot5LastBeaconSentは、送られた最後の標識フレームに関するタイムスタンプを含むように定義されました。
(7) The dot5TimerTable has been designated as obsolete.
(7) dot5TimerTableは任じられました。時代遅れ。
(8) Text has been added describing the applicability of RFC 1573 [6] to 802.5 interfaces.
(8) テキストは、RFC1573[6]の適用性について802.5のインタフェースまで説明しながら、加えられます。
(9) Other minor editorial changes.
(9) 他の小さい方の社説は変化します。
Security Considerations
セキュリティ問題
Security issues are not discussed in this memo.
このメモで安全保障問題について議論しません。
McCloghrie & Decker [Page 24] RFC 1743 IEEE 802.5 MIB using SMIv2 December 1994
SMIv2 December 1994を使用するMcCloghrieとデッカー[24ページ]RFC1743IEEE802.5MIB
Authors' Addresses
作者のアドレス
Keith McCloghrie cisco Systems, Inc. 170 West Tasman Drive, San Jose, CA 95134-1706
西タスマンDrive、キースMcCloghrieコクチマスSystems Inc.170サンノゼ、カリフォルニア95134-1706
Phone: (408) 526-5260 EMail: kzm@cisco.com
以下に電話をしてください。 (408) 526-5260 メールしてください: kzm@cisco.com
Eric B. Decker cisco Systems, Inc. 1525 O'Brien Dr. Menlo Park, CA 94025
メンローパーク、エリックB.デッカーコクチマスSystems Inc.1525オブライエン博士カリフォルニア 94025
Phone: (415) 688-8241 EMail: cire@cisco.com
以下に電話をしてください。 (415) 688-8241 メールしてください: cire@cisco.com
McCloghrie & Decker [Page 25]
McCloghrieとデッカー[25ページ]
一覧
スポンサーリンク