RFC5186 Internet Group Management Protocol Version 3 (IGMPv3) / Multicast Listener Discovery Version 2 (MLDv2) and Multicast Routing ProtocolInteraction

5186 Internet Group Management Protocol Version 3 (IGMPv3) / Multicast Listener Discovery Version 2 (MLDv2) and Multicast Routing ProtocolInteraction. B. Haberman, J. Martin. May 2008. (Format: TXT=12403 bytes) (Status: INFORMATIONAL)

日本語訳
RFC一覧

参照

Network Working Group                                        B. Haberman
Request for Comments: 5186                      Johns Hopkins University
Category: Informational                                        J. Martin
                                                           Woven Systems
                                                                May 2008


        Internet Group Management Protocol Version 3 (IGMPv3) /
          Multicast Listener Discovery Version 2 (MLDv2) and
                 Multicast Routing Protocol Interaction

Status of This Memo

   This memo provides information for the Internet community.  It does
   not specify an Internet standard of any kind.  Distribution of this
   memo is unlimited.

Abstract

   The definitions of the Internet Group Management Protocol Version 3
   (IGMPv3) and Multicast Listener Discovery Version 2 (MLDv2) require
   new behavior within the multicast routing protocols.  The additional
   source information contained in IGMPv3 and MLDv2 messages
   necessitates that multicast routing protocols manage and utilize the
   information.  This document describes how multicast routing protocols
   will interact with these source-filtering group management protocols.

1.  Introduction

   The definitions of IGMPv3 [IGMP3] and MLDv2 [MLDv2] require new
   behavior within the multicast routing protocols.  The additional
   source information contained in IGMPv3 and MLDv2 messages
   necessitates that multicast routing protocols manage and utilize the
   information.  This document will describe how multicast routing
   protocols will interpret information learned from these source-
   filtering group management protocols.

2.  Multicast Forwarding State

   Existing multicast routing protocols utilize the group management
   database in determining if local members exist for a particular
   multicast group.  With previous group management protocols, this
   database had one type of record indicating the group for which there
   was interest and the associated local interfaces.







Haberman & Martin            Informational                      [Page 1]

RFC 5186          IGMPv3/MLDv2 and Multicast Protocols          May 2008


   In the case of IGMPv3 and MLDv2, these routing protocols may now
   build multicast forwarding state based on the source filter
   information available for each multicast group that has local
   membership.  This requires that the group management database have
   four record types.  Only one record may exist for a given interface
   and a given multicast group.

      1. EXCLUDE <>
         The EXCLUDE <> record indicates interest in all sources
         destined to this group address for a set of local interfaces.
         It is equivalent to the single record type existing in previous
         versions of the group management protocols.

      2. INCLUDE <>
         The INCLUDE <> record indicates that there is no interest in
         any sources destined to this group address for a set of local
         interfaces.

      3. EXCLUDE 
         The EXCLUDE  record indicates that there is interest in
         all sources other than the specifically listed sources for a
         set of local interfaces.

      4. INCLUDE 
         The INCLUDE  record indicates that there is interest in
         only the specifically listed sources for a set of local
         interfaces.

   The records in the group management database should be utilized when
   generating forwarding state for a multicast group.  If the source
   address in the multicast packet exists in the database for the
   specified multicast group and is in an INCLUDE list or is not listed
   in an EXCLUDE list, the multicast routing protocol should add the
   interface to the list of downstream interfaces; otherwise, it should
   not be added based on local group membership.

3.  DVMRP Interaction

   The Distance Vector Multicast Routing Protocol (DVMRP) [DVMRP] does
   not incorporate any knowledge of the multicast group's senders.
   Therefore, DVMRP will act only on the multicast group address
   contained in an IGMPv3 or MLDv2 report.

   Future standardized versions of DVMRP may incorporate pruning and
   grafting messages similar to PIM-DM (discussed in Section 5).  The
   rules defined in Section 5 can be applied in this situation.





Haberman & Martin            Informational                      [Page 2]

RFC 5186          IGMPv3/MLDv2 and Multicast Protocols          May 2008


4.  MOSPF Interaction

   In Multicast Extensions to OSPF (MOSPF) [MOSPF], the consideration of
   source filter information in the group management database is limited
   to the building of forwarding state (discussed above).  This is due
   to the flooding of group-membership-LSAs within MOSPF.

5.  PIM-DM Interaction

   The PIM-DM protocol [PIMDM] interaction with a source-filtering group
   management protocol is important in two areas: multicast distribution
   tree pruning and multicast distribution tree grafting.  The following
   sections will describe the behavior needed in PIM-DM to interoperate
   with IGMPv3 and MLDv2.

5.1.  PIM-DM Prunes

   PIM-DM prune messages are initiated when a PIM-DM router determines
   that there are no entities interested in the data flowing on the
   (S,G) forwarding state.  If the multicast router is running IGMPv3 or
   MLDv2, this is determined by the source S being in EXCLUDE state in
   the source filter for the destination G, or all interest in G being
   terminated for an existing (S,G) forwarding entry.

5.2.  PIM-DM Grafts

   PIM-DM graft messages are sent in order to override an existing PIM-
   DM prune.  In the case of IGMPv3 or MLDv2, this occurs when prune
   state exists for (S,G) and a state change occurs in which the source
   filter state for S changes to INCLUDE for the specified G.

6.  PIM-SM Interaction

   A PIM-SM interaction takes place when a PM-SM [PIMSM] router receives
   an IGMP or MLD message regarding a group address that is in the Any
   Source Multicast (ASM) range.  This range is defined as the entire
   multicast address space excluding the global SSM range [SSM] and any
   locally defined Source Specific space.













Haberman & Martin            Informational                      [Page 3]

RFC 5186          IGMPv3/MLDv2 and Multicast Protocols          May 2008


6.1.  PIM-SM Joins (ASM Behavior)

   PIM-SM join messages are initiated when a PIM-SM router determines
   that there are entities interested in a specific group or a specific
   source sending to the group.  If this is due to an IGMPv3 or MLDv2
   report with a zero-length EXCLUDE list, then the join is sent as a
   (*,G) join towards the RP.

   If the join is triggered by an IGMPv3 or MLDv2 state change that
   affects source information, the PIM-SM join is sent as a (S,G) join
   towards the specific source.  This behavior optimizes the join
   process, as well as facilitates the adoption of the SSM model.  The
   generation of this (S,G) join can cause failures in architectures
   where leaf routers do not have global reachability, and thus, can be
   overridden by local policy.  If this is the case, then all triggered
   joins are sent towards the RP as (*,G) joins.  The router sending the
   (*,G) join is responsible for filtering the data as per the IGMPv3
   database before forwarding.

6.2.  PIM-SM Prunes (ASM Behavior)

   PIM-SM prune messages are initiated when a PIM-SM router determines
   that there are no entities interested in a specific group, or a
   specific source sending to the group.  If this is triggered by either
   receiving a report with an EXCLUDE or if a specific Source/Group
   times out, then an (S,G) prune is sent towards the upstream router.
   If all of the IGMPv3 or MLDv2 derived requests for a group time out,
   then (S,G) and (*,G) prunes are sent upstream as needed to stop all
   flow of traffic for that group.

7.  PIM-SSM Interaction

   A PIM-SSM interaction takes place when a PIM-SM router receives an
   IGMPv3 or MLDv2 message regarding a group address that is in the
   Source Specific Multicast range.  This behavior is not defined in
   this document, but rather in [PIMSM].

8.  Security Considerations

   This document does not introduce any additional security issues above
   and beyond those already discussed in [PIMDM], [PIMSM], [IGMP3], and
   [MLDv2].

9.  Acknowledgements

   The authors would like to thank Murali Brahmadesam, Leonard Giuliano,
   and Hal Sandick for their feedback and suggestions.




Haberman & Martin            Informational                      [Page 4]

RFC 5186          IGMPv3/MLDv2 and Multicast Protocols          May 2008


10.  Normative References

   [IGMP3] Cain, B., Deering, S., Kouvelas, I., Fenner, B., and A.
           Thyagarajan, "Internet Group Management Protocol, Version 3",
           RFC 3376, October 2002.

   [MLDv2] Vida, R., Ed., and L. Costa, Ed., "Multicast Listener
           Discovery Version 2 (MLDv2) for IPv6", RFC 3810, June 2004.

   [DVMRP] Waitzman, D., Partridge, C., and S. Deering, "Distance Vector
           Multicast Routing Protocol", RFC 1075, November 1988.

   [MOSPF] Moy, J., "Multicast Extensions to OSPF", RFC 1584, March
           1994.

   [PIMDM] Adams, A., Nicholas, J., and W. Siadak, "Protocol Independent
           Multicast - Dense Mode (PIM-DM): Protocol Specification
           (Revised)", RFC 3973, January 2005.

   [PIMSM] Fenner, B., Handley, M., Holbrook, H., and I. Kouvelas,
           "Protocol Independent Multicast - Sparse Mode (PIM-SM):
           Protocol Specification (Revised)", RFC 4601, August 2006.

   [SSM]   Holbrook, H. and B. Cain, "Source-Specific Multicast for IP",
           RFC 4607, August 2006.

Authors' Addresses

   Brian Haberman
   The Johns Hopkins University Applied Physics Laboratory
   11100 Johns Hopkins Road
   Laurel, MD  20723-6099
   US

   Phone: +1 443 778 1319
   EMail: brian@innovationslab.net

   Jim Martin
   Woven Systems
   2455 Augustine Drive, Suite 211
   Santa Clara, CA  95054
   US

   Phone: +1 408 654-8143
   EMail: jim@wovensystems.com






Haberman & Martin            Informational                      [Page 5]

RFC 5186          IGMPv3/MLDv2 and Multicast Protocols          May 2008


Full Copyright Statement

   Copyright (C) The IETF Trust (2008).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
   THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
   OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
   THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at
   ietf-ipr@ietf.org.












Haberman & Martin            Informational                      [Page 6]

一覧

 RFC 1〜100  RFC 1401〜1500  RFC 2801〜2900  RFC 4201〜4300 
 RFC 101〜200  RFC 1501〜1600  RFC 2901〜3000  RFC 4301〜4400 
 RFC 201〜300  RFC 1601〜1700  RFC 3001〜3100  RFC 4401〜4500 
 RFC 301〜400  RFC 1701〜1800  RFC 3101〜3200  RFC 4501〜4600 
 RFC 401〜500  RFC 1801〜1900  RFC 3201〜3300  RFC 4601〜4700 
 RFC 501〜600  RFC 1901〜2000  RFC 3301〜3400  RFC 4701〜4800 
 RFC 601〜700  RFC 2001〜2100  RFC 3401〜3500  RFC 4801〜4900 
 RFC 701〜800  RFC 2101〜2200  RFC 3501〜3600  RFC 4901〜5000 
 RFC 801〜900  RFC 2201〜2300  RFC 3601〜3700  RFC 5001〜5100 
 RFC 901〜1000  RFC 2301〜2400  RFC 3701〜3800  RFC 5101〜5200 
 RFC 1001〜1100  RFC 2401〜2500  RFC 3801〜3900  RFC 5201〜5300 
 RFC 1101〜1200  RFC 2501〜2600  RFC 3901〜4000  RFC 5301〜5400 
 RFC 1201〜1300  RFC 2601〜2700  RFC 4001〜4100  RFC 5401〜5500 
 RFC 1301〜1400  RFC 2701〜2800  RFC 4101〜4200 

スポンサーリンク

DROP FUNCTION ストアードファンクションを削除する

ホームページ製作・web系アプリ系の製作案件募集中です。

上に戻る